扬州市泉达金属网带厂生产的金属网带在网带式输送机运行时，输送网带跑偏是最常见的故障之一。

跑偏的原因有多种，其主要原因是安装精度低和日常的维护保养差。
1. 安装过程中，头尾滚筒、中间托辊之间尽量在同一中心线上，并且相互平行，以确保输送网带不偏或少偏。另外，网带接头要正确，两侧周长应相同。这样可以有效防止网带跑偏。
2.在使用过程中，如果出现跑偏，则要做以下检查以确定原因，进行进行调整。 
输送带跑偏时常检查的部位和处理方法有：
①检查托辊横向中心线与带式输送机纵向中心线的不重合度。如果不重合度值超过3mm，则应利用托辊组两侧的长形安装孔对其进行调整。具体方法是输送带偏向哪一侧，托辊组的哪一侧向输送带前进的方向前移，或另外一侧后移。 
②检查头、尾机架安装轴承座的两个平面的偏差值。若两平面的偏差大于1mm，则应对两平面调整在同一平面内。头部滚筒的调整方法是：若输送带向滚筒的右侧跑偏，则滚筒右侧的轴承座应当向前移动或左侧轴承座后移；若输送带向滚筒的左侧跑偏，则滚筒左侧的轴承座应当向前移动或右侧轴承座 后移。尾部滚筒的调整方法与头部滚筒刚好相反。 
③检查物料在输送带上的位置。 物料在输送带横断面上不居中，将导致输送带跑偏。如果物料偏到右侧，则皮带向左侧跑偏，反之亦然。在使用时应尽可能的让物料居中。为减少或避免此类输送带跑偏可增加挡料板，改变物料的方向和位置

扬州泉达金属网带厂承诺客户，网带可以负责安装，调试，网带可保养，做好服务是必须的，做好网带产品是必要的！

Yangzhou spring of metal mesh belt factory production of metal mesh belt running in mesh belt conveyor, conveyor mesh belt running deviation is one of the most common fault.

Run a variety of reasons, the main reason is the difference in installation of low accuracy and daily maintenance.

1. The installation process, the head tail between roller, intermediate roller in the center of the same line as far as possible, and parallel to each other, to ensure that the conveyor mesh belt unbiased or less partial. In addition, the mesh belt joint to correctly, should be the same on both sides of the circumference. So that we can effectively prevent the mesh belt running deviation.

2. In use process, if there is a wandering, is to do the following check to determine reasons, to adjust.

The conveyor belt running deviation often check the location and treatment methods are:

1) check the roller center line of the transverse and longitudinal center line of belt conveyor is not coincidence degree. Value is more than 3 mm, if you don't contact ratio should be used on either side of the roller set elongated holes on the installation and adjustment. Specific methods is a conveyor belt to which side, supporting roller group which side of the forward towards the direction of the conveyor belt move forward, backward or the other side.

(2) check the head and tail frame installation deviation of the two surfaces of the bearing. If two plane deviation is greater than 1 mm, the response to two plane adjustment in the same plane. Head roller adjustment method is: if the right side of the conveyor belt to the roller running deviation, the roller on the right side of the bearing should move forward or on the left side of the bearing seat back; If conveyor belt running deviation to drum left, the cylinder on the left side of the bearing should be move forward or on the right side of bearing seat back. The tail roller adjustment method is contrary to the head roller.

3. Check the location of the material on the conveyor belt. Material on the conveyor belt cross section is not centered, will lead to the conveyor belt running deviation. If the material slants to the right, the belt running deviation, and to the left and vice versa. When in use, should as far as possible let material center. To reduce or avoid this kind of conveyor belt running deviation can increase the baffle plate, change the direction of the material and location

Yangzhou spring metal mesh belt factory commitment to customers, mesh belt can be responsible for the installation, commissioning, mesh belt to maintain, do a good job in service is a must, it is necessary to do net belt products!